Merge pull request #4068 from iNavFlight/dzikuvx-boards-docs-update

Boards docs update

docs/Board - Matek F411 Wing.md

+# Board - [MATEKSYS F411-Wing](https://inavflight.com/shop/p/MATEKF411WING)
+
+![Matek F411 Wing](https://quadmeup.com/wp-content/uploads/2018/12/DSC_0004.jpg)
+
+## Specification:
+
+* STM32F411 CPU
+* OSD
+* BMP280 barometer
+* Integrated PDB for 2 motors
+* 2 UART ports
+* 5 servos
+* no SD card slot
+* 3 BECs
+
+## Details
+
+* [Full specification](http://www.mateksys.com/?portfolio=f411-wing)
+* For Matek F411-WING use `MATEKF411` firmware.
+* SBS pad has a built-in inverter and is connected to UART1 RX
+
+## Where to buy:
+
+* [Banggood](https://inavflight.com/shop/p/MATEKF411WING)
\ No newline at end of file

docs/Board - Matek F722-STD.md

+# Board - [MATEKSYS F722-STD](https://inavflight.com/shop/p/MATEKF722STD)
+
+![Matek F722-STD](https://quadmeup.com/wp-content/uploads/2018/12/DSC_0012.jpg)
+
+## Specification:
+
+* STM32F722 CPU
+* OSD
+* BMP280 barometer
+* Micro SD slot
+* 5 UART serial ports
+* I2C
+* 7 outputs
+* I2C
+* No BEC
+
+## Details
+
+* [Full specification](http://www.mateksys.com/?portfolio=f722-std)
+* For Matek F722-STD use `MATEKF722` firmware.
+* all serial ports are capable of running SBUS and SmartPort, no need for any additional inverters or receiver hacks
+
+## Where to buy:
+
+* [Banggood](https://inavflight.com/shop/p/MATEKF722STD)
\ No newline at end of file

docs/Board - MatekF405 Wing.md

+# Board - [MATEKSYS F405-Wing](https://inavflight.com/shop/p/MATEKF405WING)
+
+![Matek F405 Wing](https://quadmeup.com/wp-content/uploads/2018/12/DSC_0007.jpg)
+
+## Specification:
+
+* STM32F405 CPU
+* OSD
+* BMP280 barometer
+* SD slot
+* 6 UART serial ports
+* I2C
+* PDB for 2 motors
+* 7 servos
+* 5A BEC for the servos
+
+## Details
+
+* For Matek F405-WING use `MATEKF405SE` firmware.
+* SBUS pin is connected to UART2
+* SmartPort telemetry can be setup with `SoftwareSerial` feature turned on, SmartPort configured in SoftwareSerial1 and receiver connected to UART2 TX pad
+
+## Where to buy:
+
+* [Banggood](https://inavflight.com/shop/p/MATEKF405WING)
\ No newline at end of file

docs/Board - MatekF405.md

@@ -3,17 +3,10 @@
 
 ![Matek F405-AIO](http://www.mateksys.com/wp-content/uploads/2017/06/F405-AIO_2.jpg)
 
-### Matek F405-CTR
-http://www.mateksys.com/?portfolio=f405-ctr
-
-### Matek F405-STD
-http://www.mateksys.com/?portfolio=f405-std
-
-### Matek F405-AIO (end-of-life)
-http://www.mateksys.com/?portfolio=f405-aio
-
-### Matek F405-OSD (end-of-life)
-http://www.mateksys.com/?portfolio=f405-osd
+### [Matek F405-CTR](https://inavflight.com/shop/p/MATEKF405CTR)
+### [Matek F405-STD](https://inavflight.com/shop/p/MATEKF405STD)
+### [Matek F405-AIO (end-of-life)](http://www.mateksys.com/?portfolio=f405-aio)
+### [Matek F405-OSD (end-of-life)](http://www.mateksys.com/?portfolio=f405-osd)
 
 ## Firmware
 
@@ -105,7 +98,8 @@ Matek Systems: http://www.mateksys.com/
 
 ## Distributors
 
-http://www.mateksys.com/?page_id=1212
+* [Matek F405-CTR](https://inavflight.com/shop/p/MATEKF405CTR)
+* [Matek F405-STD](https://inavflight.com/shop/p/MATEKF405STD)
 
 ## FAQ & Known Issues
 

docs/Board - Omnibus F4.md

@@ -22,7 +22,7 @@
 
 ## Hardware versions
 
-### Omnibus F4 v1
+### Omnibus F4 v1 - discontinued
 
 * Linear voltage stabilizer, tends to overheat
 * SBUS inverter connected to UART1
@@ -30,7 +30,7 @@
 * 128mbit flash memory for Blackbox
 * Uses target **OMNIBUSF4**
 
-### Omnibus F4 v3
+### Omnibus F4 v3 - discontinued
 
 * Switching voltage regulator - solves problem of overheating BEC
 * SD Card slot instead of flash memory
@@ -38,7 +38,7 @@
 * PPM and UART6 can be used together when S.BUS jumper is removed (close to PPM/SBUS connector)
 * Uses target **OMNIBUSF4V3**
 
-### Omnibus F4 v4/v5
+### [Omnibus F4 v4/v5](https://inavflight.com/shop/p/OMNIBUSF4V5)
 
 * Switching voltage regulator - solves problem of overheating BEC
 * SD Card slot instead of flash memory
@@ -46,7 +46,7 @@
 * PPM and UART6 cannot be used together, there is no jumper to disconnect PPM input from UART6 RX
 * Uses target **OMNIBUSF4V3**
 
-### Omnibus F4 Pro
+### [Omnibus F4 Pro](https://inavflight.com/shop/p/OMNIBUSF4PRO)
 
 * Sometimes called Omnibus F4 v2 Pro, but also exists v3, v4 & v5 versions with no functional differences
 * Switching voltage regulator - solves problem of overheating BEC
@@ -152,6 +152,10 @@ Please note that this is *not* the motor PWM5/PWM6 pins, but small surface mount
 The SOFTSERIAL1 is an uni-directional port mapped to UART6-TX pin.
 When enabled, the UART6 is still available as hardware port but it's then RX-only port (good for e.g. receiving S.BUS input). TX instead is controlled in software and can be used for transmitting one-way telemetry (e.g. LTM). Please note that UART6-TX line passes programmable inverter on those boards, so it is a pure output-only port. SmartPort/FPort telemetry requires bi-directional communication, so it is not possible on this port without hardware modification (bypassing the inverter).
 
+## Where to buy:
+
+* [Omnibus F4 v5](https://inavflight.com/shop/p/OMNIBUSF4V5)
+* [Omnibus F4 Pro](https://inavflight.com/shop/p/OMNIBUSF4PRO)
 
 # Wiring diagrams for Omnibus F4 Pro